Hoshizaki KMD-450MAH Manuel d'utilisateur

Hoshizaki“A Superior Degreeof Reliability”www.hoshizaki.comModelsKMD-450MAHKMD-450MWHModular Crescent CuberHoshizaki America, Inc.Issued: 1-19-2009INS

10C. LocationCAUTION1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within 45°F to 100°F (7°C to 38°C

11E. Bin Control Installation1) Remove the  thumbscrews securing insulation panel (B), then remove insulation panel (B). See Fig. 3.) Disconnect the

111) Reconnect the pump motor connector and the oat switch connector.1) Replace insulation panel (B) in its correct position and secure with the 

13G. Water Supply and Drain ConnectionsSee Fig. 7, 8, or 9 WARNING1. Water supply and drain connections must be installed in accordance with applicabl

141. Icemaker• Icemaker water supply inlet is 1/" female pipe thread (FPT). A minimum of 3/8" OD copper tubing is recommended for the icema

15IcemakerDrain Outlet 3/4" FPTIcemaker Water Supply Inlet1/" FPTFig. 8Condenser Water Supply Inlet1/" FPTCondenser Drain Outlet 1/&

16Condenser Return Line Shut-Off ValveCondenser Return Line Drain ValveIcemakerDrain Outlet 3/4" FPTIcemaker Water Supply Inlet1/" FPTConde

17H. Final Checklist WARNINGCHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that

18I. Startup WARNING1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty cov

19III. Cleaning and Maintenance WARNINGCHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or m

IMPORTANTOnly qualied service technicians should install, service, or maintain this icemaker. No installation, service, or maintenance should be und

08) In bad or severe water conditions, clean the oat switch as described below. Otherwise, continue to step 9.a. Remove the  thumbscrews securing i

117) Turn off the power supply, then remove the front panel.18) Move the control switch to the "ICE" position.19) Replace the front panel i

15) Replace the front panel in its correct position.16) Clean the dispenser unit/storage bin liner using a neutral cleaner. Rinse thoroughly after c

3C. Preparing the Icemaker for Long StorageCAUTION1. When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instr

43) Open the condenser water supply line drain valve. If connected to a closed loop system, also open the condenser return line drain valve.4) Attach

5HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A7BA10A

3IMPORTANTThis manual should be read carefully before the icemaker is installed and operated. Only qualied service technicians should install, servic

4Important Safety InformationThroughout this manual, notices appear to bring your attention to situations which could result in death, serious injury,

5I. SpecicationsA. Nameplate Rating1. KMD-450MAH (self-contained air-cooled)See the nameplate for electrical and refrigeration specications. This na

62. KMD-450MWH (water-cooled)See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this

7B. Dimensions/Connections1. KMD-450MAHUnit: mm [in.]Note: 5 [0.98] increases to 101. [3.98] when lower set of mounting holes is used.

82. KMD-450MWHUnit: mm [in.]Note: 5 [0.98] increases to 101. [3.98] when lower set of mounting holes is used.

9II. Installation and Operating Instructions WARNING1. This icemaker must be installed in accordance with applicable national, state, and local regula