Hoshizaki KMD-410MAH Manuel d'utilisateur

Modular Crescent CuberModelsKMD-410MAHKMD-410MWHINSTRUCTION MANUALIssued: 7-5-2013

9• Side Panel (R): Remove the screw. Slide forward slightly and lift off.• Front Insulation: Lift up slightly, and pull towards you.• Top Insulation

10• In areas where water damage is a concern, install in a contained area with a fl oor drain.• Allow at least 6” (15 cm) clearance at the right side f

11Fig. 3Discharge HoseFloat Switch ConnectorPump Motor ConnectorThumbscrewsSnap TabPump Motor BracketFig. 4Float SwitchPump MotorCube GuideSnap Tab6b)

126) Route the bin control lead through the hole in the base, then into the bushing provided. See Fig. 5.Fig. 6Bin ControlCollarsFig. 5BushingBin Cont

1311) Replace the water tank, cube guide, pump motor bracket, pump motor and fl oat switch in their correct positions until they snap in place.NOTICEBe

14F. Electrical Connection WARNING• Electrical connection must be hard-wired and must meet national, state, and local electrical code requirements. Fa

15G. Water Supply and Drain Connections - See Fig. 9, 10 or 11WARNINGWater supply and drain connections must be installed in accordance with applicabl

161. IcemakerIcemaker WaterSupply InletMinimum IcemakerWater Supply Line SizeIcemaker DrainOutletMinimum IcemakerDrain Line Size1/2" Female Pipe

172. Water-Cooled Condensera) Connection to an Open Drain SystemCondenser WaterSupply InletMinimum CondenserWater Supply Line SizeCondenser DrainOutle

18b) Connection to a Closed Loop SystemCondenser WaterSupply InletMinimum Condenser Water Supply Line SizeCondenser Return OutletMinimum Condenser Ret

1IMPORTANTOnly qualifi ed service technicians should install and service the appliance. To obtain the name and phone number of your local Hoshizaki Cer

19H. Final ChecklistWARNINGCHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that

20I. StartupWARNINGAll parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverag

2114) Turn on the power supply to start the automatic icemaking process.15) To confi rm bin control operation, press the bin control’s actuator paddle

223) Turn off the power supply.4) Remove the front panel and move the control switch to the “SERVICE” position. Move the service switch to the “DRAIN”

23Fig. 12Discharge HoseFloat Switch ConnectorPump Motor ConnectorThumbscrewsSnap TabPump Motor BracketFig. 13Float SwitchPump MotorCube GuideSnap TabN

2412) Turn on the power supply to start the washing process.13) Turn off the power supply after 30 minutes.14) Remove the front panel.15) Move the ser

252. Sanitizing Procedure - Following Cleaning Procedure1) Dilute a 5.25% sodium hypochlorite solution (chlorine bleach) with water (add approximately

26B. MaintenanceThis icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker.WARNING• Only

27C. Preparing the Icemaker for Periods of Non-UseNOTICE• During extended periods of non-use, extended absences, or in sub-freezing temperatures, foll

285) Replace the front panel in its correct position.6) Remove all ice from the dispenser unit/storage bin. Clean the dispenser unit/storage bin using

2IMPORTANTThis manual should be read carefully before the appliance is installed and operated. Read the warnings and guidelines contained in this manu

HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com L1F043104

3Important Safety InformationThroughout this manual, notices appear to bring your attention to situations which could result in death, serious injury,

4WARNING, continued• The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or

5I. Specifi cationsA. Electrical and Refrigerant DataThe nameplate provides electrical and refrigerant data. The nameplate is located on the right side

6B. Dimensions/Connections1. KMD-410MAHUnit: mm [inches]

72. KMD-410MWHUnit: mm [inches]

8II. Installation and Operating InstructionsWARNING• Install in accordance with all applicable national, state, and local codes and regulations.• CHOK